specification mdr-10-5 mdr-10-12 mdr-10-15 mdr-10-24 model dc voltage rated current current range rated power output line regulation load regulation setup, rise time note.5 hold up time (typ.) voltage range frequency range efficiency (typ.) ac current (typ.) input inrush current (typ.) safety standards working humidity working temp. dc ok active signal (max.) storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage 5v 12v 15v 24v 2a 0.84a 0.67a 0.42a 0 ~ 2a 0 ~ 0.84a 0 ~ 0.67a 0 ~ 0.42a 10w 10w 10w 10w 80mvp-p 120mvp-p 120mvp-p 150mvp-p 5.0% 3.0% 3.0% 2.0% 1.0% 1.0% 1.0% 1.0% 5.0% 3.0% 3.0% 2.0% 500ms, 30ms/230vac 1000ms, 30ms/115vac at full load 120ms/230vac 25ms/115vac at full load 85 ~ 264vac 120 ~ 370vdc 47 ~ 63hz 77% 81% 81% 84% 0.33a/115vac 0.21a/230vac cold start 35a/115vac 70a/230vac above 105% rated output power protection type : hiccup mode, recovers automatically after fault con dition is removed 5.75 ~ 6.75v 3.75 ~ 6v / 50ma protection type : shut down o/p voltage, re-power on to recover 13.8 ~ 16.2v 9 ~ 13.5v / 40ma 17.25 ~ 20.25v 11.5 ~ 16.5v / 40ma 27.6 ~ 32.4v 18 ~ 27v / 20ma -20 ~ +70 (refer to "derating curve") 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 50 component:10 ~ 500hz, 2g 10min./1cycle, 60min. each along x, y, z axes; mo unting: compliance to iec60068-2-6 584k hrs min. mil-hdbk-217f (25 ) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. 5. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. file name:mdr-10-spec 2011-05-24 ul508, tuv en60950-1 approved, nec class 2 / lps compliant compliance to en55011, en55022 (cispr22), en61204-3 class b, en610 00-3-2,-3 compliance to en61000-4-2, 3, 4, 5, 6, 8, 11, en55024,en61000-6-1,en61204-3, light industry level, criteria a 10w single output industrial din rail power supply m d r - 1 0 s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment protection safety & emc (note 4) withstand voltage isolation resistance universal ac input/full range protections: short circuit / overload / over voltage cooling by free air convection can be installed on din rail ts-35/7.5 or 15 nec class 2 / lps compliant led indicator for power on no load power consumption<0.75w 100% full load burn-in test 3 years warranty built in dc ok active signal features : 22.5*90*100mm (w*h*d) 0.17kg; 72pcs/13.2kg/0.91cuft leakage current <1ma / 240vac function i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh emc immunity emc emission
block diagram application of dc ok active signal derating curve mechanical specification file name:mdr-10-spec 2011-05-24 -20 0 10 20 30 40 50 60 70 (vertical) 20 40 60 80 100 ambient temperature ( ) load (%) circuit detection o.l.p. emi filter rectifiers & filter power switching filter & rectifiers +v dc ok -v i/p control o.v.p. dc ok output derating vs input voltage input voltage (vac) 60hz 85 100 95 120 115 160 140 200 180 240 220 264 load (%) ta=25 90 100 80 70 60 50 40 install din rail ts35/7.5 or ts35/15 35 +v 5 5 22.5 90 5 5 -v 100 dc ok (a) 5v signal (b) led (c) relay r model 5v 12v 15v 24v r 200 1.5k 2k 3.9k v- 5.1v dc ok r v- dc ok v- relay r l case no. 956 unit:mm model model 5v 5v 12v 12v 15v 15v 24v 24v r r l 1k 120 2.4k 700 3k 700 4.7k 1.2k 5v others fg 10w single output industrial din rail power supply m d r - 1 0 s e r i e s fosc : 60khz dc ok dc ok n l
|
